Audi 100/A6

1990-1997 of release

Repair and car operation

Audi 100/A6
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   + 3.1.1.2. Technical characteristics
   - 3.1.2. 5-cylinder engines
      3.1.2.2. Technical characteristics
      3.1.2.3. Sinhronizatsionnye labels timing
      3.1.2.4. Compression check
      3.1.2.5. A gazoraspredelitelnyj belt
      3.1.2.6. Натяжитель газораспределительного a belt, an asterisk
      3.1.2.7. Additional приводной a belt
      3.1.2.8. A camshaft cover
      3.1.2.9. A camshaft epiploon
      3.1.2.10. Epiploons of a cranked shaft
      3.1.2.11. A head of cylinders
      3.1.2.12. Hydraulic pushers
      3.1.2.13. A flywheel
      3.1.2.14. Engine fastenings
      3.1.2.15. The oil pallet
      3.1.2.16. The oil pump and маслозаборный a branch pipe
   + 3.1.3. 6-cylinder engines
+ 3.2. Diesel engines
+ 3.3. Removal and a partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, a steering
+ 12. A body
+ 13. An electric equipment
+ 14. A good advice

3.1.2.5. A gazoraspredelitelnyj belt
Removal

Gazoraspredelitelnyj belt

1. A spring clip
2. The top cover of a belt
3. A gazoraspredelitelnyj belt
4. A bolt of an asterisk of a camshaft
5. A camshaft asterisk
6. Натяжитель
7. A back cover of a distributive belt
8. A bolt
9. A sealing ring of the water pump 10. The water pump
11. An asterisk of a cranked shaft
12. Bolts
13. The bottom cover газораспределительного a belt
14. A sinhronizatsionnaja label
15. A bolt
16. A pulley of a cranked shaft
17. The shock-absorber
18. A pulley and shock-absorber bolt
19. A pulley bolt

PERFORMANCE ORDER

1. Disconnect a wire of the minus plug of the accumulator.

2. Lift and fix a forward part of the car.

3. Remove a forward bumper.

4. Remove both forward headlights.

5. Disconnect a rope from the lock of a cowl and remove a cross-beam.

6. Unscrew fastenings of a radiator and shift it aside, without disconnecting from it hoses.

7. Remove the radiator fan.

8. Remove additional приводной a belt.

9. Remove натяжитель приводного a belt.

10. Establish piston N1 in ВМТ, remove the top and bottom covers газораспределительного a belt.

11. Unscrew a bolt of a pulley of a cranked shaft, preliminary having stopped a flywheel.

12. Loosen the bolts натяжителя газораспределительного a belt, turn натяжитель counter-clockwise to weaken its pressure. Remove газораспределительный a belt.

13. Remove the shock-absorber of a cranked shaft together with a belt.

Check
Examine a belt on presence of pollution by greasing or oil, and also on presence of deterioration or damages. If necessary replace a belt.
Installation

PERFORMANCE ORDER

1. Put on газораспределительный a belt and an asterisk of a cranked shaft. Tighten an asterisk bolt. The arrow specifies an adjusting ledge.

2. Combine синхронизационные labels.

3. Turn натяжитель clockwise to pull a belt. A belt will pull correctly if it can be overwound no more than on 90 °. Tighten bolts натяжителя.

4. Establish the remained details.