Audi 100/A6
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
- 3.1.1.2. Technical characteristics
3.1.1.3. Sinhronizatsionnye labels timing
3.1.1.4. Compression check
3.1.1.5. A gazoraspredelitelnyj belt
3.1.1.6. Натяжитель газораспределительного a belt, an asterisk
3.1.1.7. Additional приводные belts
3.1.1.8. A camshaft cover
3.1.1.9. A camshaft epiploon
3.1.1.10. An epiploon of an intermediate shaft
3.1.1.11. Epiploons of a cranked shaft
3.1.1.12. A head of cylinders
3.1.1.13. Hydraulic pushers
3.1.1.14. A flywheel
3.1.1.15. Engine fastenings
3.1.1.16. The oil pallet
3.1.1.17. The oil pump and маслозаборный a branch pipe
+ 3.1.2. 5-cylinder engines
+ 3.1.3. 6-cylinder engines
+ 3.2. Diesel engines
+ 3.3. Removal and a partition of engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Systems of start, ignition
+ 9. Transmission
+ 10. Brake system
+ 11. Suspension brackets, a steering
+ 12. A body
+ 13. An electric equipment
+ 14. A good advice
|
Depending on model, can be established from one to three additional belts which put in action the generator, the pump of the hydraulic booster of a wheel, the water pump and the compressor of the air conditioner.
In engines ADR the tension of the basic приводного a belt and приводного a belt of the water pump is regulated automatically.
ENGINE ADR
Removal
| PERFORMANCE ORDER |
| 1. Note a direction of rotation of a belt. |
| 2. In models with the air conditioner disconnect from the engine and a cross-beam a forward support of the engine, remove натяжитель a belt in a forward part of the engine and remove a belt from pulleys. |
|
|
| 3. To remove the basic приводной a belt, ослабьте натяжитель and stop its suitable probe. Remove a belt from pulleys. |
| 4. Stop a pulley of the pump of the hydraulic booster and unscrew bolts of a pulley of the water pump. Remove приводной a belt and two halves of a pulley. |
|
Installation and tension adjustment
| PERFORMANCE ORDER |
| 1. Put on a belt of the water pump a pulley of the pump of the hydraulic booster, establish halves of a pulley of the water pump, tighten fixing bolts and put on a belt. |
| 2. Put on pulleys the basic приводной a belt, turn натяжитель clockwise and get a lock core. |
| 3. In models with the air conditioner, put on a belt pulleys of the compressor and a cranked shaft, establish натяжитель and tighten bolts. |
| 4. Adjust a belt tension, having tightened a bolt натяжителя with a six-coal head on 25 Н.м., tighten adjusting and rotary bolts. |
|
ALL ENGINES, EXCEPT ADR
Removal
| PERFORMANCE ORDER |
| 1. Unscrew bolts of halves of a pulley of the compressor of the air conditioner and remove a pulley together with a belt. |
| 2. Loosen the fixing bolts of the pump of the hydraulic booster of a wheel also shift the pump towards a pulley of a cranked shaft. Remove a belt from pulleys. |
| 3. Loosen the fixing and adjusting bolts of the generator, ослабьте a lock bolt and, turning an adjusting nut, shift the generator back. Remove a belt from pulleys. |
|
Installation and adjustment
| PERFORMANCE ORDER |
| 1. Put on the basic belt pulleys and adjust its tension. The new belt should cave in approximately on 2,0 mm, old on 5,0 mm. |
| 2. Tighten a lock bolt, a rotary bolt and fixing bolts. |
|
|
|